Gmc sierra ticking noise when accelerating.

Once I hit 20mph or so there’s a very loud whine when accelerating but is quiet when you’re not touching the gas or if in neutral revving it there’s no noise as well. …

Gmc sierra ticking noise when accelerating. Things To Know About Gmc sierra ticking noise when accelerating.

Nov 26, 2011 · The noise sounds like air sucking or maybe a loose exhaust heat shield. The noise will stop when you take your foot off the accelerator pedal and return as soon as you press the accelerator. The noise only appears while driving, not while sitting still in park or neutral. The truck is all original and i had it up on a lift and everything is ... 10 posts · Joined 2013. #1 · Jan 26, 2013. I'm not sure under what topic to post this because I don't know where its coming from. Im getting an intermittent popping/knocking/cluncking noise felt under the driver's side floor right under my feet. It seems to only have been heard/felt when going over an elevation change or when the suspension ...724. Jun 6, 2012. #10. A couple things come to mind: 1) Check your transfer case fluid.. a dry case can make a ticking sound, you might have the infamous hole in the transfer case that many of us have had. 2) Parking Brake mounting bracket can come lose and make a sound like this...1 post · Joined 2022. #1 · Oct 24, 2022. 2017 GMC Sierra 6.2 started to develop a ticking noise from the right side of the engine. No runability problem whatsoever and no check engine light. 125k and this truck has had tons of problems already so I figure I would fix this and sell it. Searched online and found nearly unanimous that there was ...

The following are causes of timing gear or chain and sprocket noise: Worn timing chain and/or gears. Misaligned gears. Excessive backlash. A damaged tooth. Gear or sprocket loose on the shaft. Too much end play in the camshaft or crankshaft. Loose or improperly seated camshaft timing gears are usually loudest when warm.Exhaust rattle noise. 2017 GMC Sierra. First start truck rattle noise underneath truck, sounds like it is possibly coming from exhaust. Only last about 30 seconds then fades away completely. If you quickly place the truck in drive or reverse in that 30 seconds, the rattle disappears, but as soon as you put in back in park or neutral the …

Mar 30, 2012 · Noise: Clicking while decelerating from 20 miles per hour to a complete stop. Cause: Worn carrier case-side gear bores. Noise: Rumble or clicking that gets worse during hard turns. Cause: Bad wheel bearings. Noise: Driveline squeaking or grinding at any speed. Cause: Worn or damaged U-joints.

Learn how to remove a tick from your body or from a loved one. Trusted Health Information from the National Institutes of Health Removing a tick can be tricky. We've compiled a lis...Whistling noise while accelerating. Hey guys i have a 2007 nnbs with 42k miles on a 5.3. I have noticed a whistling noise, very small when accelerating near the alternator. Sounds like I have a damn cold air intake. Thinking it's a leak in a vacuum hose somewhere or the alternator is going out. Seems kinda soon for an alternator though.105 posts · Joined 2005. #1 · Dec 1, 2008. My truck 03CC 2500HD 4x4 80k miles. I've noticed my truck making this clunking sound when I come to a complete stop and when I take off. I doesn't do it all the time..but now that I hear it I am more aware of it. I would say it's been around 2 -3 weeks now and what I've been able to gather, it does ...Current Truck: 2024 GMC Sierra Denali 2500 HD with retrax-pro tonneau cover. Former Trucks:2019 GMC Sierra Denali Duramax 2500, loaded. 2016 GMC Sierra Denali Duramax Z71. every option with the exception of rear seat video. ... when I begin tk hear the sound it doesn't change the acceleration or anything, just loud and annoying.6.2L engine lifter tick. Well I have the dreaded 6.2L lifter tick at cold start up. It has kind of did it since 10k miles but now at 45k miles it is more noticeable. Lasts for 2 minutes or so. Sounds like it is a diesel when I leave for work in the morning. I run mobil 1 with acdelco filter since i bought it with 9k miles on it.

Replace your oil only AFTER you do the treatment, as the crud can get in your oil too! 2006 Chevrolet Silverado 1500HD 4x4. Metallic Silver, Duraline Bed liner, MT Tires. 6.0ltr V8, 4L80E Trans, Borla dual 2&3/4 Exhaust with X pipe, Spectre CAI, JBA Wires, NGK Laser Plugs, Backup Battery, HO Alternator, and more to come!

Ticking noise during acceleration. I just got a 17 GMC Sierra recently. 5.3L 4x4. Sometimes when I accelerate I get a ticking noise right around my drivers side. Don’t know if that’s fuel injectors or something else. Tried to get a video of it but it wasn’t loud enough. Any ideas?

1999-2002 Chevrolet and GMC C/K Pickup and Utility Models. 2002 Cadillac Escalade (2WD) with 4.8L, 5.3L or 6.0L Engine (VINs V,T,U - RPOs LR4, LM7, LQ4) Some of the above vehicles may exhibit an engine knock noise that begins in the first 19,000-24,000 km (12,000-15,000 mi) of use. The knock noise is most often noticed during initial start-up ...Clicking noise on my sierra. Hello everyone, I own a 2018 GMC Sierra All Terrain 6.2L 30k miles. Since I bought the truck I noticed a clicking noise coming from the engine bay not quite sure for the exact location but seems like the drivers side is a bit louder. I know its not a lifer noise because its super quiet on cold starts which also ...1. New Ticking Sound while driving - did not make this noise for the first 8,000 miles, it sounds identical to an exhaust manifold leak. a. It only happens when the …It has 130k miles. It just started making a loud hammering knocking sound while accelerating. Like a woodpecker on metal. It does it intermittently, less at lower speeds, most often 65 mph and over. I can make it stop by letting off the gas. The Chevy dealer tore down the transfer case, put it back together and told me to pick it up.The range (thousands of an inch) is normally etched on the edge of the gears. 3) Sampled gear wear pattern. Using a yellow marking compound, you move the gears back and forth over the sample area and note the contact pattern. Too much on the heel of the teeth would make whine on deceleration.Motor oil is important for lubricating the moving parts in your engine. When your levels get low, they don’t lubricate the valves and metal pieces properly and they may make a rhythmic ticking or clicking sound as you accelerate. [4] Other symptoms: Lit “Check Engine” light, sluggish engine, and burning smells.

The injectors are much louder and the produce a "ticking" sound when they fire . Apr 8, 2019 #15 C. cardude2000 Full Access Member. Joined Nov 12, 2015 Posts 2,931 Reaction score 1,036. ... 2008 GMC Yukon Denali - Stay away? Latest: swathdiver; 1 minute ago; General Discussion. T. Help understanding the 5.3. Latest: TheEnder53; 12 minutes ago;6.2L engine lifter tick. Well I have the dreaded 6.2L lifter tick at cold start up. It has kind of did it since 10k miles but now at 45k miles it is more noticeable. Lasts for 2 minutes or so. Sounds like it is a diesel when I leave for work in the morning. I run mobil 1 with acdelco filter since i bought it with 9k miles on it.The noise cannot be heard from the outside of the vehicle. This noise may be more noticeable on the passenger side of the vehicle and has been described as similar to the sound of running water. The dry sump oil system is hard mounted to the body of the vehicle and at cold start the oil moving through the system can transfer the noise to the body.The second step to take in case of whining noise from the transmission is to check the filter on an automatic transmission. The transmission filter is located inside the crankcase. Drain the transmission fluid with a sizable wrench. After that, unbolt the crankcase. Once the crankcase is out, check if there are metal shavings.When it did I started to notice a squeaking noise at slow speeds (usually less than 5-10 MPH) that had a consistent pattern which coincided with the speed I was going. Basically the faster I was going, the faster the squeaking. Once I get to about 10MPH that squeak has transitioned into a somewhat subtle rattle and like the squeaking, it will ...The noise sounds like air sucking or maybe a loose exhaust heat shield. The noise will stop when you take your foot off the accelerator pedal and return as soon as you press the accelerator. The noise only appears while driving, not while sitting still in park or neutral. The truck is all original and i had it up on a lift and everything is ...Exhaust manifold leaks at the head are frequently misdiagnosed as lifted tick. It is also getting closer to your t case. When you start the engine cold, feel around where the manifold meets the head. You are feeling for hot air blowing. You can also look for soot deposits. Usually the leak is in the rear.

Usually, a problem with the driveshaft will produce 4 symptoms that alert the driver of an issue that should be addressed. 1. Intense Vibrations from Underneath the Vehicle. One of the first symptoms of a problem with the driveshaft is vibrations coming from underneath the vehicle. If the driveshaft universal joint (U-joint) or bushings wear ...

#2 · Apr 6, 2011. Since it doesn't do it in neutral when you rev it, that pretty much eliminates the lifters. This sounds like an exhaust leak. Even though you can't hear it in the cab when you rev it in neutral, try listening outside under the hood & under the truck.271 posts · Joined 2015. #1 · Jan 24, 2020. My 2017 silverado has started this squeaking noise coming from the rear of the truck. It only squeaks when I accelerate from a stop and then when I come to a complete stop. I thought at first it was a shock or leaf but I can not simulate the squeak from bouncing up and down on the truck.Low fluid level. Insufficient transmission fluid level is one of the foremost causes of clicking transmission. The fluid is meant to lubricate the transmission system and prevent overheating. Running on a low fluid level will cause metal parts in the transmission system to produce a clicking sound due to a lack of proper lubrication.Get ratings and reviews for the top 11 foundation companies in Sierra Madre, CA. Helping you find the best foundation companies for the job. Expert Advice On Improving Your Home Al...Lifter Noise, Valve Tick or Piston Slap, Every GM with a 5.3, 4.8 or 4.3 does that. Dont worry about it. ... reverse, or not accelerating, no noise. But when I accelerated I had a clicking noise. Turned out to be the starter. The retention spring for the starter bendix was broken so when I accelerated, it would slide back and hit the flywheel ...It is not the pilot injection and there is nothing that you can do to stop it. It is caused by harmonic resonance from the close tolerances in new diesel engines. All diesel engines make this noise but most are too loud for it to be herd. There has even been a TSB posted about the knocking noise.G. GWB1120 Discussion starter. 1 post · Joined 2019. #1 · Jun 7, 2019. I have a 2018 Sierra 5.3 with 2300 miles on it. I just noticed a ticking sound that is coming from the front driver side of the engine. The ticking speed increase with engine RPM. Does anyone have any idea what the sound could be coming from?

AMP Powersteps: Amp Powersteps (Silverado 2014-2018): https://amzn.to/2M8tA3CToyo RT Tires: https://amzn.to/2BfzSgmRough Country 3.5” Lift: http://amzn.to/2G...

5546 posts · Joined 2010. #6 · Mar 4, 2011. If you are spinning the wheels taking off when you hear this noise it might be the G80 locking rear differential, provided you have that option. They will clunk at times when your wheels are spinning or if you are turning sharply on hard surfaces. The harder your are on the gas the more likely to ...

5546 posts · Joined 2010. #6 · Mar 4, 2011. If you are spinning the wheels taking off when you hear this noise it might be the G80 locking rear differential, provided you have that option. They will clunk at times when your wheels are spinning or if you are turning sharply on hard surfaces. The harder your are on the gas the more likely to ...In this video I have a great example of what a clicking or popping CV axle sounds like when making turns while accelerating. I even dissect the axle so that...It does not make the noise when in neutral. It will also make the noise no matter what speed I am going at. It makes the noise at any engine temp and sometimes it won't make the noise and will go away. Just today i took it up on a lift and with an auto stethoscope i manage to pinpoint the noise to be in the oil pan area about the middle.If you’re in the market for a new pickup truck, you may be considering the 2020 GMC Sierra 1500. The 2020 Sierra 1500 comes with some noteworthy improvements over the previous year...Original front end. Today, almost all the way to work (20 miles) started to get a faint grinding from the front end. When I got to work, looked for obvious stuff stuck to the axle, but nothing. Going home, it was quiet at first, but after 20 miles, same noise. The noise is almost like that of the 4wd being engaged on dry pavement.Common Causes of Rattling Noises When Accelerating. These are some of the most prevalent sources of rattling or vibration during acceleration: Loose heat shields. Exhaust system leaks or damage. Worn engine accessory belts. Transmission issues like low fluid or mount problems. Damaged or worn driveshaft components.Sep 19, 2023 · When you have a low level of oil in your engine, this will cause the components of the valvetrain to cause ticking sounds because the components are not being lubricated enough. The reason for low engine oil could be due to a leak somewhere. Perhaps you have damaged or worn out gaskets or seals. Either way, you will know if you have low engine ... In short, the clunking sound on a Chevy Silverado when accelerating is caused by the transfer case getting into contact with the skid plate. This may be caused by a damaged skid plate bending upwards or worn out transmission motor or engine mounts causing a rattling sound. Now, let’s take a look at exactly why this problem occurs, the …Engine noise after warm up 2005 5.3. Hello new to forum and first post. I have a '05 Z71 4x4 with 164K. On start up engine mostly quiet but after warm up vague ticking can be heard either side at front and through exhaust. Have listened with stethoscope everywhere and can't find obvious ticking. Few of injectors and couple coil packs make more ...This issue has gotten progressively more noticeable over the last few weeks/miles driven. On acceleration, usually starting in 3rd gear, I notice a consistent tapping/clicking noise from what seems to be the front passenger side of the car. It is NOT speed or RPM dependent, although it seems to occur above 2500 rpm.I've noticed several times that when I let off after accelerating I hear a ticking noise for about 2 seconds, then it quits. Sounds just like a noisy lifter. ... 2001-2012 GMC Sierra 2003-2009 GMC TopKick C4500/C5500 Series 2006-2012 GMC Savana Vans Equipped with Duramax(TM) Diesel Engine (RPOs LBZ, LB7, LGH, LLY, LML, LMM)

It does not make the noise when in neutral. It will also make the noise no matter what speed I am going at. It makes the noise at any engine temp and sometimes it won't make the noise and will go away. Just today i took it up on a lift and with an auto stethoscope i manage to pinpoint the noise to be in the oil pan area about the middle.Certain GMC Sierra 1500 owners may notice their pickup emitting a clicking noise around the front axle while driving. Here's why, and how to fix it. The issue is most prevalent in warmer...Have a 2009 sierra 1500 with 4.8L. Got 198,000 kms. I am original owner and have been loyal to the maintenance of the truck. Yes oil changes every 5000 kms. I am not sure on the noise. It started today. It is there whether the truck is cold or warm. makes more clunking when reving. I posted a video on You tube at the link below of the noise.Instagram:https://instagram. weokie credit union online bankingused mosquito air helicopter for saleissa myrtle beach tournamentholistic connection clarksville tn Jan 31, 2024 · Very loud ticking noise - cold start only. Last 10-20 seconds and then goes away. I have been ignoring this for months. Should I be concerned? The other day I got a check engine light, code P0300, cylinder misfire. The next day the code disappeared. Some people say its a bad lifter and I can ruin my camshaft. Others say its normal and to ignore ... greenup county courthouse docketmark chesnutt setlist 5.3 ticking sometimes. Hello everyone, so I have a 2008 Silverado with the 5.3 and it seems to have an on and off tick typically only in colder weather and not everyday. Ticking sound I recorded this clip this morning in around -11C after the truck was warming up for about 5 minutes. retinol commercial actress The ticking noise could be the universal joints having the bearings burned up causing the caps to move around on the joint. Raise up the vehicle and put it on jack stands. Start the engine and put the transmission in LOW with the transfer case in 4 HI. Listen to the front axle and try to locate the noise that the front axle is emitting.The noise could be described as an irregular ticking or clacking sound, like random typing on a mechanical typewriter. This condition has been present in diesel engines produced for the last 20 or more years. The overall noise reduction in engines produced today makes this noise seem new when, in fact, it was masked by other noises in the past.The noise was only when putting the truck into drive or reverse and under initial acceleration. Kind of sounded like rice krispys cereal for a second. Like the other poster that said he received a new driveshaft as well must of been around the same time the drive shafts were made.